Warnings
- Use the originally supplied power supply only
- Ensure the electrical outlet is protected by a Residual Current Device (RCD/GFI) with a fixed rated residual current not exceeding 30mA.
- Keep the power supply out of standing water
Position the power supply at least 3.5m/12ft away from the edge of the pool
- Do not enter the pool while the Pool Cleaner is working
- Unplug the power supply before servicing
Cautions
When not in use store the Pool Cleaner on the Caddy in a shaded area.
Use the Pool Cleaner in the following water conditions only:
Chlorine |
Maximum 4 PPM |
pH |
7.0-7.8 PPM |
Temperature |
6-35°C / 43-95°F (below 15°C / 59°F climbing performance may be affected) |
NaCl |
Maximum = 5000 PPM |
specifications
Motor protection: IP 68
Minimum depth: 0.8 m | 2.66 ft
Maximum depth: 5 m | 16.4 ft
Digital Power supply
Input: 100-125 AC Volts / 200-230 AC Volts 240v
50-60 Hertz
Output: <30 vdc
IP 54IP 44
Digital Power supply
Input:100-250 AC Volts 240v
50-60 Hertz
180 Watt
Output: 30 VDC
IP 54IP 44
The communication is at 2.4GHz frequency (for BLE and for Wi-Fi® where applicable).
IMPORTANT SAFETY INSTRUCTIONS
Please adhere strictly to the following WARNINGS
- Ensure the electrical outlet is protected by a Ground Fault Interrupter (GFI) or an Earth Leakage Interrupter (ELI).
- Keep the power supply out of standing water.
- Position the power supply at least 3.5m/12ft away from the edge of the pool.
Do not enter the pool while the Pool Cleaner is in the water.
- Unplug the power supply before servicing
- Take the Robot Pool Cleaner out of the pool before allowing people to enter the pool.
- When examining the Robot Pool Cleaner, disconnect the main power supply.
- Ensure that children do not attempt to access Robot Pool Cleaner while it is operating.
- Keep the Robot Pool Cleaner out of the reach of children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
- The unit must be connected only to a supply circuit that is protected by a ground-fault circuit interrupter (GFCI). This GFCI should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the power unit without the test button being pushed, a ground current may be flowing, indicating the possibility of an electric shock. Do not use the power unit. Disconnect the power unit and contact the manufacturer for assistance.
- Only an original power cable must be used, at all times. Replaced by a Robot Pool Cleaner certified technician, in case of need to avoid hazard.
- To reduce the risk of electric shock replace damaged cord immedietely. Do not use extension cord to connect unit to electric supply; provide a properly located outlet.
Cautions
Please ensure that the following PRECAUTIONS are implemented:
- Operator should keep hands away from driving belt mechanism.
- Position the Caddy and power supply at least 3.5m/12ft from pool’s edge – during operation.
- For continued protection against possible electric shock, the power supply unit should be placed at least 11cm/4in above ground.
- When lifting the Robot Pool Cleaner, take care to prevent back injury.
- Do not bury cord – locate cord to minimize abuse from lawn mowers, hedge trimmers and other equipment.
- This Robot is for use with permanently installed pools. Do not use with storable pools. A permanently installed pool is constructed in or on the ground or in building such that it cannot be readily disassembled for storage and reassembled to its original integrity.
When not in use, store the Pool Cleaner on its Caddy in a shaded area. Use the Pool Cleaner in the following water conditions only.
Chlorine |
Maximum 4 PPM |
pH |
7.0-7.8 PPM |
Temperature |
6-35°C / 43-95°F (below 15°C / 59°F climbing performance may be affected) |
NaCl |
Maximum = 5000 PPM |
specifications
Motor protection: IP 68
Minimum depth: 0.8 m | 2.66 ft
Maximum depth: 5 m | 16.4 ft
Digital Power supply
Input:100-250 AC Volts, 50-60Hertz, 180 Watt100-125 AC Volt, 200-230 AC Volt, 50-60Hertz, 120 Watt
Output: <30 vdc
IP 54IP 44
Bluetooth®/Wifi® Max tras power 10mW EIRR, 2.4 GHz frequency
This product is in accordance with EU Regulation & Directive 2014/531EU.
For full information, please contact us at www.maytronics.com/contact-us-en
and ask for the EC declaration of conformity.